0701-0083 Rackmount Enclosure, 7 Slots, without Fan/Shelf Controller CompactPCI Enclosure This compact 4U rack-mount chassis is a basic 40 HP system for CompactPCI Serial cards. It contains a 7-slot backplane with one CompactPCI Serial system slot and six peripheral slots. 40 HP Hybrid System This compact 4U rack-mount enclosure is a basic 40 HP system that allows the configuration with both CompactPCI Serial and CompactPCI cards. Being a hybrid system, it offers an uncomplicated and cost-effective migration solution from parallel 3U CompactPCI to serial CompactPCI Serial via the CompactPCI PlusIO standard. The 7-slot hybrid backplane in this configuration does not need a bridge or an active logic. The three slots on the left are designed for 32-bit CompactPCI and rear I/O on P2. The four slots on the right are reserved for CompactPCI Serial. The CompactPCI PlusIO system slot is the third slot from the left. This hybrid system is designed for use with duagon CompactPCI PlusIO system slot SBCs. Flexible Configuration That way, the two CompactPCI peripheral slots and two CompactPCI Serial peripheral slots as well as 2 PCI or PCI Express slots can accommodate a large range of functions. If the 2 PCI or PCI Express slots are not required, two additional CompactPCI Serial peripheral slots are available. The system supports the effortless integration of standard PCI or PCI Express cards via an adapter. The choice of modules is therefore not limited to CompactPCI cards. Harsh Environments The enclosure meets EMC requirements, making it a perfect choice for embedded applications in harsh environments. Ask us for completely configured, wired and tested systems! Rack-mountable system 3U cards vertical IEEE 1101.10/11 compliance 4U / 40 HP system 7-slot hybrid backplane 1 PSU slot CompactPCI PlusIO system slot 4 CompactPCI Serial (PICMG CPCI-S.0) peripheral slots to the right 2 CompactPCI peripheral slots to the left For duagon CompactPCI PlusIO SBCs

G201 Quad USB 3.0 Interface Board 3U CompactPCI Serial The G201 is a 3U CompactPCI Serial peripheral card offering four USB 3.0 host interfaces for high-speed applications. The G201 is a CompactPCI Serial peripheral board offering four USB 3.0 host interfaces with a data rate of up to 5 Gbit/s per direction per port (2.28 Gbit/s measured). It can be used in combination with a CompactPCI Serial or CompactPCI PlusIO CPU boardin a CompactPCI Serial or hybrid system. It is especially suited for connection of external data storage media or devices with high data transfer rate requirements, e.g. high-speed video cameras. The 4HP single Eurocard provides four USB 3.0 Standard-A connectors at the front panel.The interfaces are controlled by an xHCI controller which is connected to the backplane via a PCI Express x1 link. The G201 is screened for extended operating temperature and prepared for conformal coating for use in harsh and mobile environments. 4 USB 3.0 host interfaces Data rate up to 5 Gbit/s per direction per port -40 °C to +85 °C PICMG CPCI-S.0 CompactPCI Serial peripheral card

F215 UART, CAN Bus & Digital I/O Interface Board 3U CompactPCI The F215 is a 3U CompactPCI peripheral card offering different interface configurations for RS-232, RS-422, RS-485 UARTs, CAN bus or binary I/O. All-in-one Customizable Interface Solution The F215 is a universal interface board based on 3U CompactPCI. The physical layer can be realized individually for each channel by means of SA-Adapters. Featuring SA-Adapter Flexibility SA-Adapters are small universal boards providing the line drivers for legacy serial I/O, fieldbus interfaces and other small I/O functions. Most SA-Adapters use 9-pin D-Sub connectors which are accessible at the front panel. Alternatively, the adapter can be connected to the front panel via ribbon cable. The SA concept allows to add additional I/O interfaces to the F215, enhancing flexibility with regard to the line transceivers and isolation requirements. Tailored Extensibility Two SA-Adapters can be mounted directly on the F215, the other maximum six adapters need more front-panel space and are connected to the carrier via ribbon cable. The F215 comes in a standard configuration with five pre-defined functions on 8 HP: two CAN interfaces, two UARTs and one 8-channel digital I/O interface. SA-Adapters are not included in the delivery, because different types are available, e.g. for the UARTs. They can be ordered as needed. Multipurpose FPGA The board's I/O functions are realized by means of an FPGA, making it a very flexible, inexpensive solution for dedicated serial I/O. The card can become "everything" from a customized I/O combination to a specialized 8-port CAN card or even an intelligent I/O board including a Nios soft core, on 4, 8 or 12 HP. The FPGA is loaded automatically after power-up from a 4 MB serial Flash. It is also possible to access this Flash from the CompactPCI bus to update its contents. Ruggedized Board The F215 is designed for use in rugged environments. For example, all components are soldered-on and are specified for an operating temperature of -40 °C to +85 °C. 5 interfaces at 8 HP front: 2 UARTs, 2 CAN bus, 1 digital I/O port Other function combinations via FPGA IP cores For protocols/physical layers like RS232/RS422/RS485, HDLC, InterBus-S, CAN bus, digital I/O Physical layers via SA-Adapters -40 °C to +85 °C

M31 Mezzanine Card with 16 Digital Inputs, High-Side Switching M-Module The M31 is an M-Module with 16 digital high-side switch inputs that connect or disconnect a load to ground. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. 16-Bit Digital Input M-Module The mezzanine card M31 is a 16-bit digital input M-Module with latching capabilities for industrial applications. The inputs are optically isolated with a high isolation voltage of 500 V DC. A current limit for each input guarantees an input voltage range of 0 V to 24 V. Each input signal edge generates a maskable interrupt for each channel. The signals of mechanical switches are debounced by a digital circuit with the precision debouncing time of 300 ns to 14 ms. Based on ANSI Standard The M31 has its input load on ground which means that switching an input to supply voltage activates the respective optocoupler. Based on ANSI Standard The M31 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Reliable and Robust The M31 can operate in a -40 °C to +85 °C temperature range. The board withstands shock and vibration for reliable operation. 16 inputs 0 V to 24 V Constant current inputs Debouncing circuit Interrupt generation Load on ground Optical isolation -40 °C to +85 °C

M28 Mezzanine Card with 16 Digital Outputs, High-Side Switching M-Module The M28 is an M-Module with 16 digital high-side switching outputs that connect or disconnect a load on ground. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. The mezzanine card M28 with its open-emitter outputs can be used in process I/O applications (cf. M27 with open-collector outputs). If there are currents of above 500mA an intelligent power switch guarantees that the respective transistor is switched off. The M-Module is equipped with suppressor diodes for protection against overvoltage caused by inductive loads. The output registers can be read back. The M28 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. 16 outputs 8 V to 36 V 500 mA output current per channel Thermal and short-circuit protection Load on ground Optical isolation

M27 Mezzanine Card with 16 Digital Outputs, Low-Side Switching M-Module The M27 is an M-Module with 16 digital low-side switching outputs that connect or disconnect a load to a supply voltage. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. The mezzanine card M27 with its open-collector outputs can be used in process I/O applications (cf. M28 with open-emitter outputs). If there are currents of above 500mA an intelligent power switch guarantees that the respective transistor is switched off. The M-Module is equipped with suppressor diodes for protection against overvoltage caused by inductive loads. The output registers can be read back. The M27 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. 16 outputs 8 V to 36 V 500 mA output current per channel Thermal and short-circuit protection Load on supply voltage Optical isolation

M33 Mezzanine Card with 8 Analog Outputs, 12 Bits M-Module The M33 is an M-Module with 8 analog current or voltage outputs and 12 bits resolution. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. The mezzanine card M33 is a highly flexible M-Module for analog output signals. The isolated supply voltages can be generated by an on-board DC/DC converter. The output voltage range can be set to 0 V to 10 V, -5 V to +5 V or -10 V to +10 V for each channel by software. In addition, the current outputs can be used with 0 mA to 20 mA or 4 mA to 20 mA. The output load is driven to ground. Attention: An external supply is needed with 8 current outputs! The M33 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. 8 current or voltage outputs 12 bits resolution 10 µs acquisition/conversion time Simultaneous channel update Optical isolation -40 °C to +85 °C versions

M32 Mezzanine Card with 16 Digital Inputs, Low-Side Switching M-Module The M32 is an M-Module with 16 digital low-side switch inputs that connect or disconnect a load to a supply voltage. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. 16-Bit Digital Input M-Module The mezzanine card M32 is a 16-bit digital input M-Module with latching capabilities for industrial applications. The inputs are optically isolated with a high isolation voltage of 500 V DC. A current limit for each input guarantees an input voltage range of 0 V to 24 V. Each input signal edge generates a maskable interrupt for each channel. The signals of mechanical switches are debounced by a digital circuit with the precision debouncing time of 300 ns to 14 ms. Low-Side Switching The M32 has its input load on supply voltage which means that switching an input to ground activates the respective optocoupler. Based on ANSI Standard The M32 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Reliable and Robust The M32 can operate in a -40 °C to +85 °C temperature range, depending on the product model. The board withstands shock and vibration for reliable operation. 16 inputs 0 V to 24 V Constant current inputs Debouncing circuit Interrupt generation Load on supply voltage Optical isolation

G227 Wireless Network Board for 2 PCIe and 10 Micro-SIM Cards 3U CompactPCI Serial The G227 is a rugged single Eurocard CompactPCI Serial carrier board supporting the PCI Express Mini Card standard for implementing WLAN, UMTS, GPS, GSM or HSDPA interfaces. The G227 is a rugged single slot CompactPCI Serial carrier board for up to three PCI Express Mini Cards. Two PCI Express Mini Card slots are by default equipped with two RP-SMA antenna connectors / cables each. Other types of antenna connectors are available on request. These slots can be used for UMTS, GSM, HSPA, LTE modems. Fields of Application The G227 provides connectivity solutions to cellular networks by adding LTE, UMTS, GSM or other types of wireless modems. It is intended for use in various train connectivity applications including onboard WLAN, passenger infotainment and fleet management systems. In the train communication system architecture, the G227 is typically located at the front end where it communicates directly with a cellular network. To optimize the connection and network coverage, the G227 features ten microSIM card slots. Software duagon provides a user friendly software tool designed for interacting with the G227. The user is able to remotely control which microSIM cards are connected to the modems. Remote power reset is also possible for each modem and the third optional PCI Express Mini Card module. Suited for harsh and mobile environments The G227 is designed for -40 to +85°C operating temperature and conformal coated in order to be used also in harsh and mobile environments. The final environmental qualification depends on the respective PCI Express Mini Cards used with the carrier. 2 PCI Express Mini Card slots for LTE, UMTS, GSM, HSPA communication 2 external antennas per module (reverse SMA) 1 PCI Express Mini Card slot for WLAN, GPS, virtual SIM card, audio codec 1 external antenna optional 10 microSIM card slots Software tool for switching SIM cards and remote power up/down of modems -40 °C to +85 °C, conformal coating PICMG CPCI-S.0 CompactPCI Serial peripheral card

M43N Mezzanine Card with 8 Relay Outputs M-Module The M43N is an M-Module for free potential switching of 8 signals. It is designed for industrial automation, medical computers, in-vehicle computers, and embedded computers in transportation. Multiple Relay Outputs The mezzanine card M43N is a relay output M-Module for potential-free switching of eight signals. The status of each relay can be read out via "read-modify-write" access. The relays implemented guarantee highest reliability and long life. The board is based on the M-Module ANSI mezzanine standard and can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Flexible and Cost Saving The M43N is fully compatible to the predecessor M-Module M43 which means no changes in application design are necessary. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Robustness and Long-Term Availability The rugged board withstands shock and vibration for reliable operation and a longer product life-time. It is mainly designed for industrial process I/O applications. With a guaranteed standard life-time of 7 years from product start, M43N facilitates the client’s life-cycle management by making the overall system available at least for this period of time. 8 relay outputs 1 A switching power per relay One throw-over contact per relay Output voltage range max. 48 V No separate supply voltage -40 °C to +85 °C