M56 16-Channel Analog Multiplexer M-Module The mezzanine card M56 is an M-Module which has 16 relay channels with throw-over contacts. The mezzanine card M56 is an M-Module which has 16 relay channels with throw-over contacts. It is a switching matrix for measuring signals with different voltage levels and different ground references. The powerless-switching relays offer great advantages: since there are no thermoelectric potentials, the M56 can "process" very small voltage and current. The M56 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. 16 powerless-switching relays 1 µA to 50 mA (max. 50 V), ±1.25 V, ±2.5 V One throw-over contact each No separate supply voltage Low heat development Optical isolation -40 °C to +85 °C

M50 Synchro/Resolver Converter M-Module The mezzanine card M50 is a 1-channel, continuous-tracking synchro- or resolver-to-digital converter M-Module with a configurable 10 to 16-bit resolution. The mezzanine card M50 is a 1-channel, continuous-tracking synchro- or resolver-to-digital converter with a configurable 10 to 16-bit resolution and a tracking rate of up to 1040 rps. The M-Module has a reference signal generator with a frequency range of 50 Hz to 20 kHz. Reference output voltages can be in a range of 2 Vrms to 21 Vrms. An analog velocity output can be used to monitor the rotational speed. The M-Module is suited for nearly all synchro/resolver sensors: the user can easily adapt the M50 by plugging passive components. The M50 is optically isolated and supplied by an on-board DC/DC converter. Optical isolation of the digitized values significantly improves accuracy compared to common transformers. The M50 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Resolver/synchro-to-digital converter Up to 16 bits resolution On-board reference frequency generation On-board signal conditioning 2 arc minutes accuracy Analog velocity output Optical isolation -40 °C to +85 °C Not conforming to RoHS

F608 Side Card for RAID Systems 3U CompactPCI The F608 is a 4HP SATA extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. The F608 is a 4HP SATA extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. It offers four SATA interfaces over a SATA port multiplier via PCI Express as well as one SATA slot on-board (from the chipset). Two individually configurable UARTs are accessible via D-Sub connector at the front. Two USB and two PCI Express links are available via rear I/O. As an option, the F608 also offers the possibility to realize two optical Ethernet interfaces via SFP. The F608 is directly plugged to the right side of the respective single-board computer. A robust connector makes for high mechanical stability. It is delivered with an 8HP front panel, replacing the 4HP front panel of a 3U single-board computer and thus resulting in a solid one-piece front panel. The operating temperature range is 0..60°C. 4/8 HP extension for 3U Intel SBCs F14, F15, F17, F18, F19P, F21P 4 SATA ports via J2 rear I/O RAID 0, 1 and 5 support CompactPCI PlusIO compliant 1 SATA hard-disk slot 2.5" on board 2 COMs via SA-Adapters Optical isolation depending on SA-Adapter Two optical Gigabit Ethernet interfaces via SFP as an option

F604 Side Card FireWire 3U CompactPCI The F604 is a 4HP FireWire and multimedia extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. The F604 is a 4HP FireWire and multimedia extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. The IEEE 1394 high-speed serial bus is often used in combination with modern high-end digital camera equipment instead of USB. Thus, the F604 side-card extends the standard features of a powerful multi-core or Pentium M CPU board by one 400 MBit/s FireWire interface connected via PCI Express links. It further provides a DVI-D single link port, an HD audio - in or out - port as well as one, optionally two COM interfaces. In addition an onboard 2.5" SATA hard-disk slot is available on the F604. The F604 is directly plugged to the right side of the respective single-board computer. A robust connector makes for high mechanical stability. It is delivered with an 8HP front panel, replacing the 4HP front panel of a 3U single-board computer and thus resulting in a solid one-piece front panel. 4 HP extension for 3U Intel SBCs F14, F15, F17, F18, F19P, F21P 1 IEEE 1394 interface 1 DVI-D Single Link 1 HD Audio (in or out) 1 or 2 RS232 2.5" SATA hard-disk slot

F302 Managed Industrial Ethernet Switch 3U CompactPCI The F302 is a managed 3U Fast Ethernet switch module with a maximum of eight channels at the front panel plus one additional rear Ethernet channel. Managed Fast Ethernet Switch The F302 is a managed 3U Fast Ethernet switch module with a maximum of eight channels at the front panel (8 RJ45 or M12 connectors) plus one additional Ethernet channel that is led to the CompactPCI J1 connector at the rear. PowerPC CPU and Front Panel Service Interface The F302 is managed by its own PowerPC CPU that integrates the configuration firmware. A service interface is accessible at the front panel, providing an easy way to configure the switch. A command line interface is available via the RS232 at the service port and over Ethernet via Telnet or Secure Shell (SSH). The switch can also be configured via SNMP (version 3). Additionally, the service connector can be used to attach an external dongle to store or update the switch configuration. This makes it easy to exchange the unit for service purposes. Reliable Communication System Component The F302 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward-switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security as well as the logical segmentation of ports (802.1q VLANs). The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol / link aggregation) and no data loss occurs. Its built-in test mechanisms make the F302 an even more reliable component in the communication system. Fully Compliant to Railway Standards The F302 was specifically designed for rugged mobile communication systems. It is thus for example fully compliant with the EN 50155 railway standard. All components on the board are specified for a -40°C to +85°C operation temperature. There are no socketed components, hardening the card against shock and vibration. The board is ready for coating (standard with M12 connectors) and has a guaranteed minimum standard availability of 5 years. Depending on the connector type, the F302 has a front-panel width of 12 HP (3 slots) with RJ45 or 16 HP (4 slots) with M12 connectors. In either case the card occupies only one CompactPCI backplane slot. Managed 8+1-Port rugged Ethernet switch 12 or 16 HP 32-bit/33-MHz CompactPCI 8 Fast Ethernet ports (front) on RJ45 or M12 connectors Configuration via Telnet CLI, SNMP ver. 3 or external dongle Switch accessible via cPCI for router applications Service interface via D-Sub LEDs for port and board states -40°C to +85°C with qualified components EN 50155 compliant (railways)

F301 Unmanaged Industrial Ethernet Switch 3U CompactPCI The F301 is an unmanaged 3U Fast Ethernet switch module with a maximum of 8 channels at the front panel (8 RJ45 or 6 D-Sub connectors) and an integrated Fast Ethernet controller. Unmanaged Fast Ethernet Switch The F301 is an unmanaged 3U Fast Ethernet switch module with a maximum of 8 channels at the front panel (8 RJ45 or 6 D-Sub connectors) and an integrated Fast Ethernet controller. The Ethernet switch is an unmanaged device, meaning that it is not recognized by other CompactPCI devices thereby removing the need for additional software. As an option it is also available as a fixed managed device, with a customized, hardware-coded configuration. Onboard Ethernet Controller An onboard Ethernet controller is used to realize the interface to the CompactPCI bus. The F301 also works without the Ethernet controller being assembled. In this case the CompactPCI bus only delivers the power supply. As an option (with the Ethernet controller not being assembled) the J2 connector can be assembled and used to manage the rear I/O Ethernet signals from the ninth Ethernet port. Compliant to Railway Standards he F301 is specifically designed for rugged mobile communication systems. It is thus, for example, fully compliant with the EN 50155 railway standard. All components on the board are specified for a -40°C to +85°C operation temperature. The board is ready for coating. The F301 needs one slot on the CompactPCI bus, using a 4 HP or 8 HP front panel. Unmanaged 8+1-Port rugged Ethernet switch 8 HP 32-bit/33-MHz CompactPCI 8 Fast Ethernet ports (front) 1 Fast Ethernet controller (rear J1) Option: 1 Fast Ethernet port (rear J2) -40°C to +85°C with qualified components

F210 GSM/GPS/UART Interface 3U CompactPCI The F210 is a rugged single Eurocard CompactPCI GSM/GPS/UART interface that needs only one slot on the CompactPCI bus. The F210 is a rugged single Eurocard CompactPCI GSM/GPS/UART interface that needs only one slot on the CompactPCI bus. The board is equipped with a GSM-R device that is used in rolling stock and commercial vehicles like buses or trucks. GSM-R was specified to support train safety and is introduced at the UIC organization as EIRENE (European Integrated Railway radio Enhanced NEtwork) project. The F210 supports the EGSM 900 and GSM 1800 frequency bands. A separate GPS device is implemented on the F210 to combine the receiving function of any kind of positioning data with the transmitting possibilities of a mobile phone. The highly sensitive GPS receiver supports 20-channel GPS technology, and is capable of acquisition and tracking in very low signal-strength environments. This allows effective and reliable operation in all scenarios. The GPS and GSM units are optically isolated from all other parts of the board. In addition to the GPS and GSM functionality the F210 offers two SA-Adapter slots for serial interfaces with RS232 or RS422 or RS485 line drivers, with or without isolation. As an option, another three SA-Adapters can be connected to the F210 for user-defined functions like even more serial interfaces (synchronous/asynchronous) and/or fieldbusinterfaces like CAN bus or IBIS. These user-defined functions can be implemented as IP cores in an onboard FPGA. Robust Reverse SMA connectors provide the physical interface to the external GSM and GPS antennas. The F210 is screened for extended operation temperature and conformally coated for use in harsh and mobile environments. 4 HP 32-bit/33-MHz CompactPCI GSM-R (Rail) EGSM 900 / GSM 1800 GPS according to NMEA 0183 GPS and GSM optically isolated from other functions 2 UARTs via SA-Adapters FPGA for further user-defined functions 2 Reverse SMA connectors to external antennas -40°C to +85°C screened Conformal coating

F50C PowerPC MPC8548 Conduction Cooled SBC 3U CompactPCI F50C is a versatile, rugged MPC8548/MPC8543 PowerPC CPU board in 3U CompactPCI format for embedded applications with conduction cooling. The F50C is a versatile, rugged PowerPC based single-board computer for embedded applications with conduction cooling. It is controlled by an MPC8548, or optionally an MPC8543 PowerPC CPU (alternatively with encryption unit) with clock frequencies between 800 MHz and 1.5 GHz. The SBC is equipped with ECC-controlled, soldered-on DDR2 RAM for data storage, with up to 16 GB of solid-state Flash disk for program storage as well as industrial FRAM and SRAM. The CPU card provides up to three Gigabit Ethernet channels, four USB ports, up to two SATA interfaces and up to 64 user-definable I/O lines controlled by its onboard FPGA. These interfaces can be combined in many variations and are all available at the rear using the board's J2 connector. For first operation and service purposes, the board also includes a UART-to-USB port accessible at the front panel. The F50C is based on a standard 3U CompactPCI card that is embedded into a dedicated CCA frame for conduction cooling (CCA = conduction cooled assembly). The 9-HP assembly can be used with duagon's conduction-cooled subrack. It is designed for operation in a -40°C to +85°C environment. For convection cooling, the F50P model is also available, which comes with a tailor-made heat sink for extended temperatures. The large FPGA on the F50C allows to add additional user-defined functions such asgraphics, touch, serial interfaces, fieldbus controllers, binary I/O etc. for the needs of the individual application in an extremely flexible way. Before boot-up of the system, the FPGA is loaded from boot Flash. Updates of the FPGA contents can be madeinside the boot Flash during operation. Equipped with a PCI-bridge chip, the F50C offers a full CompactPCI interface (system slot functionality) for reliable system expansion. Apart from that, the F50C can also be used as a busless, stand-alone board, with power supply from the backplane. The soldered components on the F50C withstand shock and vibration, and the board design is optimized for conformal coating. The F50C comes with MENMON support. This firmware/BIOS can be used for bootstrapping operating systems (from disk, Flash or network), for hardware testing, or for debugging applications without running any operating system. 32-bit/33-MHz cPCI system slot 1 slot, 9 HP front, rear I/O MPC8548 (or MPC8543), up to 1.5 GHz Up to 2 GB (ECC) DDR2 SDRAM Up to 128 KB FRAM, 2 MB SRAM Up to 16 GB SSD Flash FPGA for user-defined I/O functions MENMON BIOS for PowerPC cards -40°C to +85°C Tcase screened Conduction cooling

DC2 Rugged 10.4" Touch Panel PC Industrial Display Computer The panel PC DC2 is a rugged, fanless and maintenance-free human-machine interface for interactive applications in transportation and industrial automation. The panel PC DC2 is a rugged, fanless and maintenance-free human-machine interface (HMI) for interactive applications in transportation and industrial automation. It is designed for panel mounting and equipped with a 10.4" 4:3 LCD TFT display with a capacitive touch panel. The DC2 is controlled by the Intel Atom XL Z520PT running at 1.33 GHz and comes with 1 GB of DDR2 SDRAM and a built-in 2-GB microSD card. The standard interfaces comprise 2 Fast Ethernet (via RJ45 connectors) and 2 USB ports as well as four binary inputs (via the 10-pin power supply connector). The two Ethernet interfaces have switch functionality to provide Ethernet connection to subsequent intelligent displays. A temperature sensor is provided to monitor and controlthe display. All I/O signals are concentrated at the bottom of the unit. The DC2 is equipped with an internal 10 V to 36 V (12 VDC nom. or 24 VDC nom.) wide-range power supply and able to operate in a -40°C to +70°C environment (+85°C for 10 minutes). It complies with the EN 50155, class Tx railway standard when used with an optional includable PSU suited for railway applications. All electronic components are soldered to withstand shock and vibration and prepared for conformal coating. The unit's control electronics are directly attached to the back of the display, hence bigger screen sizes or other aspect ratios can be realized easily. Further options include other types of the Intel Atom XL processor, M12 connectors for the Ethernet interfaces, a serial interface or GPS adapter that can be added via an SA-Adapter, HD audio via a D-Sub connector and an antenna connector. A PCI Express Mini card slot (with a SIM card slot) in combination with an external antenna can be used to incorporate wireless functions like GPS, GLONASS, Wi-Fi, WIMAX, GSM/GPRS, UMTS, HSDPA and LTE. 10.4" 4:3 TFT LCD with capacitive touch panel 1024 x 768 pixels resolution Intel Atom processor 2 Fast Ethernet, 2 USB Wide-range PSU, 12/24 VDC nom. -40°C to +85°C operating temperature Fanless and maintenance-free design Compliant to ISO 7637-2 (E-mark for automotive), IP65 (front), IP20 (rear)

M79 Profibus DP Slave Interface M-Module The mezzanine card M79 is a Profibus DP interface M-Module (slave) based on the Infineon C165 CPU. The mezzanine card M79 M-Module is a Profibus DP (Distributed Peripherals) slave interface based on the Infineon C165 CPU. It is thus an ideal interface solution for intelligent remote I/O applications via a very popular fieldbus standard. The C165 CPU handles communication with the host CPU via the on-board shared DRAM. The advantage of this Profibus implementation is that the complete Profibus protocol stack runs locally on the M-Module with very reduced interaction of the host CPU. The RS485 Profibus interface (9-pin D-Sub) allows selectable transmission rates from 9.6 kbit/s up to 12 Mbit/s. The optically isolated interface is supplied by an on-board DC/DC converter. The output is short-circuit protected. The M79 comes with 512 KB local Flash, 1 MB local SRAM and 16 KB dual-ported RAM. Profibus slave functionality comprises initialization and termination of slaves, additional status information on output and input data as well as security services such as DP applications checked by a user watchdog or a protocol stack monitored by the application. The Profibus firmware consists of the true Softing protocol stack. The corresponding driver software comes from duagon and complies with standard Softing tools. It supports configuration of the M79 for each application in a very convenient way. The driver is based on MDIS ( Modular Driver Interface System) which makes the M79 ready for use under Windows, Linux and RTOS environments. The M79 is based on the M-Module ANSI mezzanine standard. It can be used as anI/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Profibus DP slave (DIN19245) Isolated RS485 Local 16-bit CPU 12 Mbit/s data transfer rate Complete Softing Profibus software on board Compatible with Softing tools