M54 DC Motor Controller M-Module The mezzanine card M54 is a motor controller M-Module that is suited for all types of motors that have a ±10V DC control input. The mezzanine card M54 is a motor controller that is suited for all types of motors that have a ±10V DC control input and that can provide a position feedback information using an incremental encoder (e.g. servo motors). The motor controller componenton the M54 is able to move a motor to a specific position at a specific speed. The PID values for the controller can be defined by software and thus be adapted to the motor used. In addition there are eight binary inputs and two binary outputs, which are isolated from each other, from the analog output and from the system. The M54 is based on the M-Module ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. 1 LM628 supported channel For every motor type with ±10 V control input Position and velocity operation Quadrature incremental encoder interface PID values programmable RS422 or TTL, ±10 V, 1 relay output Additional binary I/O Optical isolation Not conforming to RoHS

G302 Managed 16-Port Rugged Industrial Ethernet Switch 3U CompactPCI Serial The G302 is a rugged managed 3U Gigabit Ethernet switch implemented as a CompactPCI Serial board with up to 16 Ethernet ports. Managed Industrial Ethernet Switch The G302 is a managed 3U Ethernet switch implemented as a CompactPCI Serial board. It occupies one system slot or one peripheral slot, using a 4 HP front panel with 3 Gigabit Ethernet ports on RJ45 or M12 connectors and one service interface via M12. The G302 either features three Ethernet ports on the front and up to 13 Ethernet ports on the rear or alternatively all 16 Ethernet ports on the rear, which is the ideal solution for conduction cooling. Reliable Communication System Component The G302 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security. The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol/link aggregation) and no data loss occurs. Its built-in test mechanisms make the G302 an even more reliable component in the communication system. Compliant to Railway Standards The railway Ethernet switch is specifically designed for rugged mobile communication systems and fully compliant with the EN 50155 railway standard, qualified for a -40°C to +85°C operation temperature and ready for coating. Managed 16-port rugged Ethernet switch Up to 16 Gigabit Ethernet ports on rear I/O Or 3 ports on front and up to 13 ports on rear Configuration via Telnet CLI, SNMP ver. 3 or external dongle Service interface via M12 LEDs for front port and board states -40°C to +85°C with qualified components EN 50155 class TX compliant (railways) PICMG CPCI-S.0 CompactPCI Serial system slot and peripheral card

G301 Unmanaged 4-Port Rugged Industrial Ethernet Switch with PoE 3U CompactPCI Serial The G301 is an unmanaged 3U Gigabit Ethernet switch implemented as a CompactPCI Serial board with 4 Gigabit Ethernet ports on RJ45 connectors. Unmanaged Industrial Ethernet Switch The G301 is an unmanaged 3U Ethernet switch implemented as a CompactPCI Serial board. It occupies one peripheral slot, using a 4 HP front panel sporting 4 Gigabit Ethernet ports on RJ45 connectors. Options include M12 front connectors and a P6 connector for the rear I/O Ethernet signals from the board's fifth Gigabit Ethernet port. Reliable Communication System Component The G301 supports full-duplex and half-duplex operation with auto-negotiation and high-speed non-blocking store-and-forward switching. The switch is fault tolerant and restores itself on its own. Its built-in test mechanisms make the G301 an even more reliable component in the communication system. In addition, the switch can act as Power over Ethernet (PoE) Power Sourcing Equipment (PSE), supplying other devices on all ports with up to 7W (class 1, 2) per port for power according to IEEE 802.3 Section 2 - Type 1, class 1 and 2 (formerly known as IEEE 802.3af). The maximum power available for one G301 is limited to 28 W, according to CPCI-S.0 specification. Compliant to Railway Standards The board is specifically designed for rugged mobile communication systems. It is thus for example fully compliant with the EN 50155 railway standard, screened for a -40°C to +85°C operation temperature and ready for coating. Unmanaged 4-port rugged Ethernet switch 4 Gigabit Ethernet (front) on RJ45 (M12 optional) Power over Ethernet (PoE) PSE (all ports) LEDs for link and activity status 1 Gigabit Ethernet on rear I/O (optional) -40°C to +85°C (screened) EN 50155 class TX (railways) PICMG CPCI-S.0 CompactPCI Serial peripheral card

G100 CompactPCI Serial to CompactPCI Interface Card 3U CompactPCI Serial The G100 is used in combination with the F100 to connect a CompactPCI Serial system to a CompactPCI system. The G100 is used in combination with the F100 to connect a CompactPCI Serial system to a CompactPCI system. The CompactPCI Serial backplane and the CompactPCI backplane can either be located in one housing or in two separate ones. The G100 is plugged into a peripheral slot of a CompactPCI Serial system and is connected to the F100 via a PCI Express cable at the front which can have a length of up to 7 m. The F100 functions as the system slot in the CompactPCI system. The G100 uses one PCI Express x1 link from the backplane and leads it to the front to an 18-pin PCI Express connector. The board is qualified for operation in the extended temperature range of -40°C to +85°C. For operation together with F100 system slot card for CompactPCI 1 PCI Express x1 link -40°C to +85°C with qualified components PICMG CPCI-S.0 CompactPCI Serial peripheral card

F605 Side Card XMC/PMC 3U CompactPCI The F605 is a 4HP XMC or alternatively PMC extension card for 3U Intel based CompactPCI single-board computers F15, F17, F18 and F19P. The F605 is a 4HP XMC or alternatively PMC extension card for 3U Intel based CompactPCI single-board computers F15, F17, F18 and F19P. The XMC slot supports either one PCI Express link with 4 lanes on one XMC connector or 1 link with one lane on each ofthe two XMC connectors . The PMC slot can be used for 32/64 bit and 33/66 MHz PMC cards and supports up to 133 MHz PCI-X. The board detects automatically whether an XMC or a PMC is plugged. The F605 is directly plugged to the right side of the respective single-board computer. A robust connector makes for high mechanical stability. It is delivered with an 8HP front panel, replacing the 4HP front panel of a 3U single-board computer and thus resulting in a solid one-piece front panel. 4 HP extension for 3U Intel SBCs F15, F17, F18, F19P 1 XMC slot (PCIe 1 x4 link or 2 x1 links) or 1 PMC slot (32/64 bits, 33/66/133MHz, PCI-X) PMC rear I/O support via J2 (only in 32-bit backplane) -40°C to +85°C with qualified components

F601 Side Card for Multimedia 3U CompactPCI The F601 is a multimedia extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. The F601 is a multimedia extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. A variety of graphics, audio and serial interfaces characterize the functionality of the F601. Depending on the combination of these functions, the F601 may take one slot (4HP) or two slots (8HP) alongside the CPU card. The two DVI interfaces supporting the digital PanelLink technology deliver a maximum of 1600 x 1200 pixels in true-color mode. Together with the analog CRT interface from the CPU board it is possible to connect two monitors. The audio interface supports the high definition standard. SA-Adapters provide different physical layers for the UART interface, so that the F601 can be configured flexibly with either RS232, RS422 or RS485, alternatively isolated or not isolated. In addition an onboard 2.5" SATA hard-disk slot is available. The F601 is directly plugged to the right side of the respective single-board computer. A robust connector makes for high mechanical stability. It is delivered with an 8HP or 12HP front panel, replacing the 4HP front panel of a 3U single-board computer and thus resulting in a solid one-piece front panel. 4/8 HP extension for 3U Intel SBCs F14, F15, F17, F18, F19P, F21P 2 DVI connections 1 HD audio 1 COM, alternatively with optical isolation 2.5" SATA hard-disk slot

F100 CompactPCI to CompactPCI Serial Interface Card 3U CompactPCI The F100 is used in combination with the G100 to connect a CompactPCI Serial system to a CompactPCI system. The F100 is used in combination with the G100 to connect a CompactPCI Serial system to a CompactPCI system. The CompactPCI Serial backplane and the CompactPCI backplane can either be located in one housing or in two separate ones. The F100 is plugged into the system slot of the CompactPCI system. It is equipped with a PCI-Express-to-PCI bridge which acts as a master for up to 7 PCI devices. It supports 32-bit and 33-MHz. The F100 is connected to the G100 via a PCI Express cable at the front panel which can have a length of up to 7 m. The G100 is located in a peripheral slot of the CompactPCI system. Optionally the F100 can also be used without the G100 if the PCI Express x1 link is led to the board via the backplane. For this, a special backplane isneeded, however. Another possibility is to directly control a CompactPCI system using an external PC (e.g. a notebook) for evaluating or programming the application. The board is qualified for operation in the extended temperature range of -40 up to +85°C. 4 HP 32-bit/33-MHz CompactPCI Replaces system slot card For operation together with G100 peripheral slot card for CompactPCI Serial 1 PCI Express x1 link

D202 PC-MIP Carrier Board 6U CompactPCI The D202 is a 6U PC-MIP carrier board for universal I/O on the CompactPCI bus. The D202 is a 6U PC-MIP carrier board for universal I/O on the CompactPCI bus. You can install up to six PC-MIPs on the D202, with four Type I/II and two Type I PC-MIPs. All PC-MIPs provide I/O via the J3/J4/J5 CompactPCI connectors of the D202, while the four Type II modules are also accessible at the front panel. Even equipped with six PC-MIPs, the D202 needs only one slot on the CompactPCI bus. PC-MIPs are an ideal solution for flexible and fast CPU-related applications, which take advantage out ofthe internal PCI bus of the PC-MIPs. 1 CompactPCI bus slot 6 PC-MIP slots

A602 PowerPC Safe Computer 6U VME64 The A602 is a 6U, 64-bit VME COTS computer, certifiable up to SIL 4 and DAL-A, with triple redundancy for functional safety on a single board to achieve fail-operational, fault-tolerant behavior. The A602 is a 6U 64-bit VME COTS computer with onboard functional safety that realizes triple redundancy on a single board to achieve fail-operational, fault-tolerant behavior. The board can also act as a fail-silent subsystem, i.e. it can shut down in case of a fatal fault. Its complex FPGA-based design helps dramatically lower software development costs as it automatically manages the system's triple-redundant processors and memory. The result: The system's redundant architecture is fully taken advantage of by software designed for a standard single-CPU board. The A602 is designed for deterministic operation and offers extensive BITE features (e.g., ECC error counters for all types of memory, monitoring of all internal voltages), internal buses with error correction and fault-tolerant (fail-operational) implementation. Its three processors run in lockstep mode with 2-out-of-3 (2oo3) voting implemented in FPGA and software-assisted resynchronization, while its triple redundant dynamic memory automatically corrects upsets caused by cosmic radiation (SEU) and hardware faults. The system is powered by redundant local power supplies with separate power supplies for the three CPUs and the three main memory ranks. The A602 has been developed according to DO-254, compliant to DO-160 and certifiable up to DAL-A in avionics applications. Additionally, the product meets the requirements of EN50128/EN50129 and can be deployed in signalling and rolling stock applicationsup to SIL 4. All I/O is realized in SEU-resistant FPGAs and available on the system's rear connectors. Additionally, the A602 offers two PMC slots with rear I/O for PMC1. As an option, the second PMC slot can be customized for an AFDX PMC (rear I/O only). A second A602 can be connected to build a high reliability/availability cluster. The two A602s exchange data via a sextuple UART connection and a BMCX link. 3x PowerPC 750 (lockstep mode), 3x 512 MB DDR RAM Fail-operational, fault-tolerant behavior Fail-safe and fail-silent board architecture Clustering of two A602 to raise availability Board management, BITE SEU (radiation) tolerant Certifiable up to SIL 4 (with report from TÜV SÜD) and DAL-A Developed according to RTCA DO-254, EN 50129 and IEC 61508 EN 50155 compliance Up to -40 to +70°C with qualified components Convection or conduction cooling

G20 Intel Core i7 CPU Board 3U CompactPCI Serial The G20 is a 4HP/3U CompactPCI Serial CPU card supporting USB, SATA, PCI Express and Gigabit Ethernet rear I/O interfaces according to the CPCI-S.0 standard. The G20 is a versatile 4HP/3U single-board computer supporting a multitude of modern serial interfaces according to the CompactPCI Serial standard. It is thus perfectly suited for data-intensive applications which require high computing-power. The CPU card is equipped with Intel's Core i7 processor running at up to 3.2 GHz maximum turbo frequency and offering multi-core architecture from Intel with full 64-bit support. The G20 supports the Intel Active Management technology which makes it possible to access the board via the network even when it is in soft-off or standby state. The memory configuration of the G20 includes a state-of-the-art fast DDR3 DRAM which is soldered to the board to guarantee optimum shock and vibration resistance. An mSATA disk connected via a SATA channel and a microSD card device which is connected via a USB interface offer nearly unlimited space for user applications. The board delivers an excellent graphics performance. Two DisplayPort interfaces are accessible at the boardfront. Using an external adapter two HDMI or two DVI ports can also be realized. In addition the standard front I/O comprises two PCIe-driven Gigabit Ethernet and two USB 2.0 ports. Serial interfaces at the rear I/O connectors are 8 USB, 6 SATA interfaces, one DisplayPort or HDMI (instead of one interface at the front panel), 5 PCI Express x1 links, and two PEG x8 links. Up to eight Gigabit Ethernet interfaces can be realized using a rear I/O adapter board. Thermal supervision of the processor and a watchdog for the operating system complete the functionality of the G20. The G20 operates in Windows and Linux environments as well as under real-time operating systems that support Intel's multi-core architecture. The InsydeH2O EFI BIOS was specially designed for embedded system applications. The G20 is suited for a wide range of industrial applications, e.g. for monitoring, vision and control systems as well as test and measurement. Main target markets comprise industrial automation, multimedia, traffic and transportation, aerospace, shipbuilding, medical engineering and robotics. The G20 comes with a tailored passive heat sink within 4 HP height. The robust design of the G20 makes the board especially suited for use in rugged environments with regard to shock and vibration according to applicable DIN, EN or IEC industry standards. The G20 is also ready for coating so that it can be used in humid and dusty environments and has a guaranteed minimum standard availability of 7 years. Intel Core i7, 2.53 GHz Dual-core 64-bit processor PICMG CPCI-S.0 CompactPCI Serial Up to 4 GB DDR3 DRAM soldered, ECC mSATA and microSD card slots Standard front I/O: 2 DisplayPorts, 2 Gb Ethernet, 2 USB Standard rear I/O: 7 PCIe, 8 USB, 6 SATA, DisplayPort/HDMI Rear I/O via mezzanine board: up to 8 Gigabit Ethernet Intel Turbo Boost 2.53..3.2 GHz, Hyper-Threading, Active Management Technology Open CL 1.1 support