EM1N Embedded System Module COM with MPC5200B Computer-On-Module The EM1N Computer-On-Module is an MPC5200B PowerPC based embedded SBC for use in different industrial environments, with custom I/O in an onboard FPGA and front connectors. The EM1N Computer-On-Module can be supplied as a stand-alone module, with an application-specific carrier card and/or with additionally plugged PCI-104 modules. The EM1N is controlled by the MPC5200B PowerPC processor which was specially developed for automotive applications and which operates at up to 400 MHz and 700 MIPS. The complete ESM module in standard form has an operational temperature of -40 to +85°C. The CPU consumes less than 1 W at 384 MHz. The EM1N is equipped with up to 256 MB soldered SDRAM and up to 1 GB NAND Flash as well as with 16 MB additional SDRAM, up to 8 MB boot Flash and 2 MB battery-backed SRAM. The EM1N provides two Fast Ethernet interfaces, one serial line and USB 1.1 at its front panel. As an alternative to RJ45, D-Sub connectors guarantee reliable functions also in harsh environments. Two CAN controllers with V2.0A/B CAN protocol are included in the MPC5200B. The physical CAN interfaces are accessible via SA-Adapters. Further UARTs and other additional I/O functions can berealized in the on-board FPGA and accessed via a carrier board. The functionality of the FPGA is dynamically loaded by the application software. The EM1N comes with MENMON support. This firmware/BIOS can be used for bootstrapping operating systems (fromdisk, Flash or network), for hardware testing, or for debugging applications without running any operating system.The EM1N is designed to operate under harsh environmental conditions including -40 to +85°C operation temperature, shock, vibration, humidity. It focuses on applications in transportation (railways), automotive and avionics. For a first evaluation of the functions of the EM1N it is strongly recommended to use the EK6N ESM starter kit. The kit consists of the standard CPU module, an FPGA loaded with additional I/O functions, the carrier card with I/O connectors, an external PSU, VGA and RJ45 to D-Sub cables, and an adapter for mounting a PCI-104 module. ESM modules are complete computers which consist of the hardware (CPU, chip set, memory, I/O) which is not fixed to any application-specific function, and an FPGA programmed in VHDL code for user-defined I/O. ESM modules are based on PCI. They have two system connectors: J1 has a fixed signal assignment, while J2 is variable depending on the final application-specific configuration of the ESM and the carrier board. J2 also feeds the I/O signals of the functions programmed in the FPGA to the carrier card. MPC5200B / 384 MHz FPGA 18,752 LEs (225,000 gates) Up to 256 MB onboard DDR SDRAM Up to 8 MB boot Flash, NAND Flash 2 MB SRAM, 16 MB additional SDRAM Dual Ethernet, COM, USB 1.1 (front) Dual CAN controller on carrier User defined I/O functions (COMs, graphics, IDE etc.) optional via FPGA on carrier Stackable with PCI-104 MENMON BIOS for PowerPC cards -40°C to +85°C qualified

A302 128-Channel Binary I/O Card 6U VMEbus The A302 is an input/output VMEbus target board for 128 binary process signals. The I/Os are divided into four optically isolated units. The card is used for input/output of digital signals with different voltage levels and ground references. The A302 is an input/output VMEbus target board for 128 binary process signals. The I/Os are divided into four optically isolated units. The card is used for input/output of digital signals with different voltage levels and ground references. For each unit 32 channels are driven to a 44-pin D-Sub connector. Each channel can be either input or output. The binary inputs/outputs can be universally used in industrial systems. They are optically isolated from the system, which is essential for advanced automotive and industrial applications. 1-slot A24/D16 VMEbus slave 4 optically isolated units 32 channels for each unit Individual use of each channel as input or output Individual edge-triggered interrupts Input/output load on ground High-side output switches Output current 1.9 Aper channel or 16 A per unit Over-current and over-temperature protection

P511 Dual Fast Ethernet PMC PCI Mezzanine Card The P511 is a dual Ethernet USM-based mezzanine PMC supporting an FPGA MAC layer and six additional GPIOS. The P511 is a 32bit/33MHz PMC with dual Ethernet functionality. The two channels can be accessed via two RJ45 connectors which are led to the front via an adapter cable from a SCSI connector. They support half duplex and full duplex operation. The PMC offers the possibility to buffer all receive and transmit Ethernet frames either in a local or in an external data buffer. This makes it possible to provide a Worst Case Execution Time analysis which makes it particularly well suited for safety-critical applications. Up to 6 GPIO lines can be used on the module for additional functionality. The P511 is based on the USM concept. USM Universal Submodules make PMC modules more flexible than ever. The Ethernet functionality is realized via an IP core implemented inside its onboard FPGA. This function can be changed at any time through implementation of different IP cores. The corresponding line drivers are realized on the USM which is simply plugged on the P511. One alternative function is the combination of an Ethernet core with a fieldbus interface to build gateways. The I/O mezzanine module is suitable for any PMC compliant host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC in telecommunication, industrial, medical, transportation or aerospace applications. It offers long-term availability for at least 10 years and is qualified for operation in the extended temperature range. 2 full-duplex or half-duplex channels 10Base-T and 100Base-TX physical layer MAC layer realized in FPGA Local or external data buffer 6 additional GPIOs Fully integrated to comply with IEEE802.3 500 VAC isolation voltage -40 to +85°C with qualified components 32-bit/33-MHz PMC PMC based on USM concept Individual FPGA configuration

F206N Nios II Slave Board 3U CompactPCI The F206N is a 3U CompactPCI card with an onboard Altera Cyclone FPGA and the integrated Nios II soft processor. The F206N is a 3U CompactPCI card with an onboard Altera Cyclone FPGA and the integrated Nios II soft processor. It is designed for final use in volume in an application and it acts at the same time as the standard FPGA development platform for this application. Due to its multitude of directly accessible I/O pins the F206N can be used as a universal FPGA platform. With the Nios II CPU inside the FPGA, the F206N can for example act as an intelligent slave on the CompactPCI bus. In any case the F206N supports a nearly endless range of applications. Examples may include functions such as an intelligent 8-channel CAN controller with DMA and local protocol stack, real-time Ethernet controller, analog front end with DSP-like pre-computing, intelligent counter, intelligent HDLC interface etc. The Cyclone FPGA acts as the main controller. It supports a 32-bit/33-MHz CompactPCI bus, controls the SDRAM memory and has read/write access to the Flash memory. The special FPGA-Flash structure provides initial programming using a boundary scan interface and later, with a configured FPGA, the device may be updated at any time with data from the CompactPCI bus. The FPGA also controls four status LEDs and up to 79 user-defined I/O pins. A total of 32MB soldered SDRAM and 2MB Flash back the potential computing functionality of the F206N. The F206N is designed for use in rugged environments. For example, all components are specified for an operation temperature of -40 to +85°C. For development of the application duagon provides a Nios - CompactPCI open platform FPGA development package that includes a sample design with an internal PCI system unit, integrating the standard Wishbone and the Altera Avalon bus. 32-bit/33-MHz CompactPCI Peripheral slot function FPGA 12,000 LEs (approx.144,000 gates) Nios II soft processor 32 MB SDRAM, 2 MB Flash Flexible FPGA-Flash structure Open platform FPGA development package Support of Wishbone and Avalon bus -40°C to+85°C with qualified components

P601 Quad Redundant Gigabit Ethernet XMC PCI Mezzanine Card The P601 is a Gigabit Ethernet XMC mezzanine card with four 10/100/1000Base-T channels and two x4 PCIe links on the XMC connector. The P601 is a Gigabit Ethernet XMC mezzanine card suitable for any XMC compliant single-board computer or host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Compared to PMC, the XMC standard defines a different board-to-board connector for support of PCI Express. The four Ethernet channels on the P601 are provided by two Ethernet controllers with two lines each and supported by two PCIe links with four lanes each. With a specific set-up the two lines inside each Ethernet controller can be used as a redundant channel pair. In this mode one line is monitored by the other line and the controller recognizes when an error occurs. The mezzanine module P601 is typically suited as an extension for Windows and Linux based systems with a heavy demand for multiple and ultra-fast communication requirements. As such it is used in high-bandwidth multi-channel communication applications in networked appliances such as base stations, routers, switches, gateways, residentialgateway controllers, etc. Main target markets comprise telecom, medical engineering and transportation. For use in rugged environments the P601 is delivered with a passive heat sink and is prepared for conformal coating. Equipped with Intel components that come exclusively from the Intel Embedded Line, the P601 has a guaranteed minimum standard availability of 5 years. Four 10/100/1000Base-T channels 1 XMC connector with 2 x4 PCIe links Alternatively two redundant channel pairs 4 RJ45 connectors at front Full and half duplex 1.5 kV electrical isolation

SF4 Unmanaged 8-port Rugged Ethernet Switch with M12 3U 19" Industrial Stand-Alone Device The SF4 is a stand-alone, unmanaged industrial Fast Ethernet switch that comes in a compact 3U, 22HP, 19" cassette. It was specifically designed for rugged mobile systems, e.g., in transportation. The SF4 is a stand-alone, unmanaged industrial Fast Ethernet switch that comes in a compact 3U, 22HP, 19" cassette. It provides eight channels at the front panel accessible through M12 connectors. The SF4 is supplied by its integrated, rugged power supply unit (PSU), with a power connector at the front panel. The entire switch consumes less than 7 W and needs no cooling. The SF4 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security. The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol / link aggregation) and no data loss occurs. Its built-in test mechanisms make the SF4 an even more reliable component in the communication system. In addition, the switch can act as Power over Ethernet (PoE) Power Sourcing Equipment (PSE), supplying other devices on ports 1 and 2 with power. By using an application-specific configuration EEPROM, the SF4 can act similarly to a managed switch with fixed settings. This enables features untypical for unmanaged models like 802.1p priority and port based priority, port based VLAN or IEEE 802.1q VLAN IDs. Additionally, a service port is accessible at the front panel on an M12 connector, enabling authorized personnel to configure the switch via an SPI interface. The SF4 was specifically designed for rugged mobile communication systems with high demands. It is thus for example fully compliant with the EN 50155 railway standard. All components inside the cassette are specified for a -40 to +85°C operation temperature. There are no socketed components, hardening the box against shock and vibration. Its PCBs are conformally coated and the switch has a guaranteed minimum standard availability of 5 years. Unmanaged 8-port rugged Ethernet switch 3U, 22 HP, 19" rack mountable 8 Fast Ethernet ports (front) on M12 connectors Power over Ethernet PSE functionality Service interface via D-Sub LEDs for port, PoE and board states Wide input range PSU (14.4 to 154 V), EN 50155 qualified (railways) -40 to +70(+85)°C according to EN 50155 Class Tx with qualified components Conformal coating

SF3 Managed 8-port Rugged Ethernet Switch with M12 3U 19" Industrial Stand-Alone Device The SF3 is a stand-alone, managed industrial Fast Ethernet switch that comes in a compact 3U, 22HP, 19" cassette. It was specifically designed for rugged mobile systems, e.g., in transportation. The SF3 is a stand-alone, managed industrial Fast Ethernet switch that comes in a compact 3U, 22HP, 19" cassette. It provides eight channels at the front panel accessible through M12 connectors. It is supplied by its integrated, rugged power supply unit (PSU), with a power connector at the front panel. The entire switch consumes less than 7 W and needs no cooling. The SF3 is managed by its own PowerPC CPU that integrates the management firmware. A service port is accessible at the front panel on a D-Sub connector, providing an easy way to configure the switch. A command line interface is available via the RS232 at the service port and over Ethernet via Telnet or Secure Shell (SSH). The switch can also be configured via SNMP (version 3). Additionally, the service connector can be used to attach an external dongle to store or update the switch configuration. This makes it easy to exchange the unit for service purposes. All of the ports are individually configurable. The SF3 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward-switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security as well as the logical segmentation of ports (802.1q VLANs). The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol / link aggregation) and no data loss occurs. Its built-in test mechanisms make theSF3 an even more reliable component in the communication system. In addition, the switch can act as Power over Ethernet (PoE) Power Sourcing Equipment (PSE), supplying other devices on ports 1 and 2 with power. The SF3 was specifically designed for rugged mobile communication systems with high demands. It is thus for example fully compliant with the EN 50155 railway standard. All components inside the cassette are specified for a -40 to +70°C operation temperature (+85°C for ten minutes according to EN50155 Class Tx). There are no socketed components, hardening the box against shock and vibration. Its PCBs are conformally coated and the switch has a guaranteed minimum standard availability of 5 years. Managed 8-port rugged Ethernet switch 3U, 22 HP, 19" rack mountable 8 Fast Ethernet ports on M12 connectors Power over Ethernet PSE functionality Configuration via Telnet CLI, SNMP ver. 3 or external dongle Service interface via D-Sub LEDs for port, PoE and board states Wide input range PSU (14.4 to 154 V), EN 50155 qualified -40 to +70(+85)°C according to EN 50155 Class Tx with qualified components Conformal coating

SF2 Managed 8-port Rugged Ethernet Switch with RJ45 3U 19" Industrial Stand-Alone Device The SF2 is a stand-alone, managed industrial Fast Ethernet switch that comes in a compact 3U, 18HP, 19" cassette. It was specifically designed for rugged mobile systems, e.g., in transportation. The SF2 is a stand-alone, managed industrial Fast Ethernet switch that comes in a compact 3U, 18HP, 19" cassette. It provides eight channels at the front panel accessible through RJ45 connectors. It is supplied by its integrated, rugged power supply unit (PSU), with a power connector at the front panel. The entire switch consumes less than 7 W and needs no cooling. The SF2 is managed by its own PowerPC CPU that integrates the management firmware. A service port is accessible at the front panel on a D-Sub connector, providing an easy way to configure the switch. A command line interface is available via the RS232 at the service port and over Ethernet via Telnet or Secure Shell (SSH). The switch can also be configured via SNMP (version 3). Additionally,the service connector can be used to attach an external dongle to store or update the switch configuration. This makes it easy to exchange the unit for service purposes. All of the ports are individually configurable. The SF2 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward-switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security as well as the logical segmentation of ports (802.1q VLANs). The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol / link aggregation) and no data loss occurs. Its built-in test mechanisms make the SF2 an even more reliable component in the communication system. In addition, the switch can act as Power over Ethernet (PoE) Power Sourcing Equipment (PSE), supplying other devices on ports 1 and 2 with power. The SF2 was specifically designed for rugged mobile communication systems with high demands. It is thus for example fully compliant with the EN 50155 railway standard. All components inside the cassette are specified for a -40 to +70°C operation temperature (+85°C for ten minutes according to EN 50155 Class Tx). There are no socketed components, hardening the box against shock and vibration. Its PCBs are ready for coating and the switch has a guaranteed minimum standard availability of 5 years. Managed 8-port rugged Ethernet switch 3U, 18 HP, 19" rack mountable 8 Fast Ethernet ports on RJ45 connectors Power over Ethernet PSE functionality Configuration via Telnet CLI, SNMP ver. 3 or external dongle Service interface via D-Sub LEDs for port, PoE and board states Wide input range PSU (14.4 to 154 V), EN 50155 qualified -40 to +70(+85)°C according to EN 50155 Class Tx with qualified components

SF1 Unmanaged 8-port Rugged Ethernet Switch with RJ 45 3U 19" Industrial Stand-Alone Device The SF1 is a stand-alone, unmanaged industrial Fast Ethernet switch that comes in a compact 3U, 18HP, 19" cassette. It was specifically designed for rugged mobile systems, e.g., in transportation. The SF1 is a stand-alone, unmanaged industrial Fast Ethernet switch that comes in a compact 3U, 18HP, 19" cassette. It provides eight channels at the front panel accessible through RJ45 connectors. The SF1 is supplied by its integrated, rugged power supply unit (PSU), with a power connector at the front panel. The entire switch consumes less than 7 W and needs no cooling. The SF1 supports full-duplex and half-duplex operation with auto-negotiation, high-speed non-blocking store-and-forward switching, Quality of Service (QoS) support with four traffic classes IEEE 802.1p and three-level 802.1x security. The switch is fault tolerant and restores itself on its own: If a link is temporarily unavailable, frames can be sent via backup/redundant links (spanning tree protocol / link aggregation) and no data loss occurs. Its built-in test mechanisms make the SF1 an even more reliable component in the communication system. In addition, the switch can act as Power over Ethernet (PoE) Power Sourcing Equipment (PSE), supplying other devices on ports 1 and 2 with power. By using an application-specific configuration EEPROM, the SF1 can act similarly to a managed switch with fixed settings. This enables features untypical for unmanaged models like 802.1p priorityand port based priority, port based VLAN or IEEE 802.1q VLAN IDs. Additionally, a service port is accessible at the front panel on an M12 connector, enabling authorized personnel to configure the switch via an SPI interface. The SF1 was specifically designed for rugged mobile communication systems with high demands. It is thus for example fully compliant with the EN 50155 railway standard. All components inside the cassette are specified for a -40 to +85°C operation temperature. There are no socketed components, hardening the box against shock and vibration. Its PCBs are ready for coating and the switch has a guaranteed minimum standard availability of 5 years. Unmanaged 8-port rugged Ethernet switch 3U, 18 HP, 19" rack mountable 8 Fast Ethernet ports (front) on RJ45 connectors Power over Ethernet PSE functionality Service interface via D-Sub LEDs for port, PoE and board states Wide input range PSU (14.4 to 154 V), EN 50155 qualified (railways) -40 to +70(+85)°C according to EN 50155 Class Tx with qualified components

PU8 Power Supply Unit, 36 VDC, 100 W 3U 12 HP PSU The PU8 is a plug-in power supply unit for 19" systems (e.g. VMEbus, CompactPCI) and is especially designed for computer systems in public transport vehicles, being fully compliant with EN 50155. The PU8 is a plug-in power supply unit for 19" systems (e.g. VMEbus, CompactPCI) and is especially designed for computer systems in public transport vehicles, being fully compliant with EN 50155. The PU8 has a nominal input voltage of 36 VDC with a wide input range of 25.2 V to 45 V and a maximum input voltage range of 21.6 V to 50.4 V (according to EN 50155). The otherwise identical PSU models PU5 and PU6 are available for the nominal input voltages of 110 VDC and 24 VDC, respectively. It is controlled by a microprocessor which supervises the voltage and the temperature as well as one external input (for its key input function) and one output. Thanks to the onboard intelligence the PSU can also act as an SMBus slave and communicate with the CPU board via the backplane. This allows the PSU to power on the system at a programmed date and enables the CPU to make status polls with regard to, e.g., error messages, time-out or on/off. The PSU provides a DC/DC converter to generate the isolated 12 V from the input voltage. Two regulators generate 5 V and 3.3 V from the 12 V isolated side. The maximum power at full load is 100 W total, with 40 W on 3.3 V and 60 W on 5 V. The minimum power is 5 W. The microprocessor is supplied with power independently and can turn off the main DC/DC converter to switch the unit into standby mode (power consumption less than 2 W). The subassembly is conformally coated, and components are secured against vibration. The PSU operates in -40 °C to +85 °C environmental temperature. The thermal stress is extremely low due to integrated heat sinks and diversion of dissipated heat over the mounting surface. The exact configuration and features of PU8 vary depending on the ordered model. 3U, 12 HP, 19" rack mountable Input 36 VDC nom. (25.2 to 45 V) Max. input voltage range 21.6 to 50.4 V (according to EN 50155) Output 3.3 V, 5 V, 12 V H15 DIN 41612 plug connector (front and rear) SMBus External I/Os for key input function Standby mode (1 W max.) -40 °C to +85 °C Conformal coating EN 50155 compliant (holdup time according to Class S2) (railways)